Wiring Diagrams Explained | How to Read Wiring Diagrams

Wiring Diagrams Explained | How to Read Wiring Diagrams

How to Read Electrical Diagrams?

In this article, you’ll learn how to read, understand and use a wiring diagram.

An electrical wiring diagram could be a single page schematic of how a ceiling fan should be connected to the power source and its remote switches.

A wiring diagram may include the wirings of a vehicle. For example, how the horns are powered and connected to the controller on your steering wheel.

Or an electrical wiring diagram can be a 200-page document including all the electrical wirings of an electrical control panel in a huge factory or plant.

As some rules of thumb will be applied to most of the wiring diagrams, in Part 1 of this multi-part article you’ll learn how to read a wiring diagram by means of an actual industrial control panel’s wiring diagram.

And in Part 2, you’ll learn how to read a PLC wiring diagram and its modules. 

Spend Some Time on Understanding the Standards!

Wiring diagrams may follow different standards depending on the country they are going to be used.

They may have different layouts depending on the company and the designer who is designing that.

They also may be drawn by different ECAD software such as EPLAN or AutoCAD electrical. So, when you see a wiring diagram for the first time, you may need some time to analyze it and become familiar with its layout and symbols.

Wiring Diagram Software

Let’s start with an actual example of a wiring diagram.

The document we are going to check includes more than 140 pages but we’ll check only some of the pages as the rest of them are somehow similar.

First Things First! Wiring Diagram Symbols 

Every wiring diagram includes:

– Hardware components,

– Power sources,

– Ground chassis,

– Terminals,

– Some wires of course!

– Numbers, letters, and maybe some nomenclatures.

Wiring Diagram Symbols

Normally the very first step to learn reading a wiring diagram is becoming familiar with the symbols of the equipment and each wiring diagram is supposed to have a page or two for this purpose.

This page is known as Legend and abbreviation page.

Legend and Abbreviation

In the Legend and Abbreviation page you can see:

– A three-phase AC electric motor symbol

– A solenoid valve symbol

– An MCCB with thermal and short circuit protection

– A contactor (the coil and its contacts)

and all the other electrical symbols you need to read the wiring diagram.

Electrical Wiring Diagram Symbols

Remember that these symbols may have some minor differences in different wiring diagrams depending on the ECAD software they have been designed with.

As an example, the Fuse in EPLAN Electric P8 (a Wiring Diagram Software) looks like this:

EPLAN Electric Symbols

But in AutoCAD electrical, it looks like this:

AutoCAD Electrical Symbols

By the way, you’ll learn more symbols in the rest of this article and you’ll get used to these electrical symbols very soon!

Wiring Diagram Rules of Thumb!

Ok, let’s start with the first page to see how much it could be easy to read and understand a wiring diagram.

Wiring Diagrams and Schematics

Rule #1: How to Follow a Wiring Diagram (Reading Direction)

First of all, there is a rule of thumb in standard wiring diagrams that you should read the diagram from left to right and from top-down.

Exactly like reading a book!

How to Trace a Wiring Diagram

But sometimes, designers make some exceptions to have a better layout such as this page.

So as an exception, we should start from the downside and this is where the three-phase power enters the panel.

How to Read Wiring Diagrams Electrical

As a reminder, the voltage level and the frequency of the power depends on the country we’re implementing our project.

For example:

– In England or Austria, the voltage level is 400 volts with 50 hertz of frequency

– In the United States, a three-phase power source will produce 480 volts with 60 hertz of frequency.

Three Phase Electrical Power Standard in Countries

The power enters the terminal blocks with the “X0” terminal strip.

The terminal strip is a mark that refers to a group of terminal blocks with the same voltage level or the same purpose.

What is Terminal Strip

From these terminal blocks, we move on to a three-pole circuit breaker with thermal and short circuit protection capability.

Three Pole Power Circuit Breaker Symbol

Rule #2: Wiring Diagrams Are Drawn in the Neutral Condition

Every standard wiring diagram should be drawn in the neutral condition.

This means that all of the contacts, contactors, circuit breakers, etc., are shown in their normal or non-energized condition.

Therefore, when you see a closed contact in an electrical wiring diagram, that is a normally closed contact and the rest of the contacts should be open.

We have a great article about NO and NC contacts and their actual application examples that you can read it here.

NO and NC Contacts in Wiring Diagrams

How to Read Wiring Diagrams

Ok! Let’s continue reading.

After closing this circuit breaker manually, the power flows toward some power distributer bars, from which some branches can be taken.

How to Follow a Wiring Diagram

One of the branches goes into a two-pole circuit breaker.

Two Pole Circuit Breaker Symbol in Wiring Diagram

and from there powers a transformer.

Transformer Symbol in Wiring Diagram

If you’ve noticed, there are some numbers on the wires.

These are called “wire tags”.

Wire Tags in Wiring Diagram

What is a Wire Tag? (And Device Tag)

Wire Tags are the combination of some letters and numbers installed on the wire or cable and are used to show you to which device or terminal block a wire or a cable should be connected.

What is a Wire Tag

Wire tags are very helpful in case of troubleshooting so that when a wire gets out of its connection point, you can easily look at the wiring diagram and figure out where it should be connected again.

How to Use Wire Tags

There are the tags for the devices within the panel as well.

If you were looking at the wiring diagram and you didn’t know what a device is, then you could find it in the panel using its tag.

Device Tags

This transformer converts the 400 volts to a single-phase 230 volts.

400 to 230 Transformer

It is used to feed the power receptacle or socket, the heater, and the fan.

Electrical Control Panel Wiring Diagram

The “-ST19” tag refers to a thermostat to turn on and off the heater or the fan on its specified temperature setpoints.

Thermostat Symbol in Wiring Diagram

You’ve also noticed the earthing chassis and its branches wherever it’s needed.

Earthing Chassis in Electrical Wiring Diagram

How to Address a Component in Wiring Diagrams

Before we continue to the next page, you may ask what these numbers on top of the page are. This is a very good question!

Understanding Wiring Basics

Actually, these are the column numbers and they have divided each page of this drawing to 10 columns.

As you see, there are some devices in each column and we can use these column numbers in combination with the page number to address different devices, contacts, terminal blocks, and so on, in other pages.

Let me explain it by some examples!

Wiring Diagram Layouts

For instance, the main three-phase power is shown with some arrows and numbers on the top right-hand side of the page.

All of them have a 2.0 number just beside the arrow.

– By “2” it refers us to page two.

– By “0” it points out to the first column of page two.

Wiring Diagrams Addressing System

And there you go! It’s our power source on page two.

Addressing a Component in Electrical Wiring Diagram

As another example, the number below this contact says page 130 and column 6.

Learn How to Read a Wiring Diagram

I’ll turn to page 130 of the wiring diagram and this is column number 6.

Learn to Read Electrical Wiring Diagrams

And there it is! The same tag, KA1306 as we had expected.

It looks like a coil. But not the coil of a contactor; the coil of a relay.

And how do I know that?! If you have seen the legend and abbreviation page of the drawing you know that the “-KA” is a nomenclature for a relay in this drawing.

Relay in Wiring Diagrams

Below the coil, you see the 13-14 contact (NO Contact) of page two and also the other NO and NC contacts of this relay with the addresses they have been used in this drawing.

We’ll get back to this page again.

Relay NO Contact in Wiring Diagram

On page two, the mains power source is feeding a 24-volt power supply and it provides us with a voltage of 24 with 10 amps of capacity.

Power Supply Symbol in Wiring Diagram

From there, we have extended this voltage using some terminal blocks so that we can deliver the power to different instruments, PLC cards, PLC CPU, or whatever device which needs 24 volts to power on.

Learn to Read Wiring Schematics

But wait! This part of the drawing, seems a little bit strange as all of these terminal blocks have the same tag of “XC”.

What are Double-Level Terminal Blocks?

Terminal Blocks Symbol in Wiring Diagram

There are a variety of terminal blocks in the market. In this case, to save some space in the panel, we have used some double-Level terminal blocks.

Double Deck Terminal Blocks

They occupy the same space as the ordinary terminal blocks but we can connect two wires to each side of them.

Double Level Terminal Block

In the following, we have a branch that delivers the 24 volts power to page 12 column zero, but with two interlocks!

Design Wiring Schematic

What is Electrical Interlocking?

An interlock means a condition.

For example, here, without having those interlocks enabled, our 24 v cannot reach page 12, column 0.

Electric Interlock

Let’s turn to page 130 of the wiring diagram again to see what those conditions are.

What is an Interlock

NOTE: Did you notice that we have to get back and forth between different pages? This is the only way we have to take to fully understand these drawings.

On page 130, we’ve a safety relay, and it will be used to protect people, material, and the machine itself when the machine is operating.

Safety Relays in Wiring Diagrams

Remember that the designer of this wiring diagram had to refer to the datasheet of this equipment to complete his job.

Safety Relay Datasheet

In fact, reading the datasheet of the equipment is a very important and inevitable stage of designing a wiring diagram.

We should always do the same thing for all of the equipment used in the process.

Safety Relay Circuit Diagram

By the way, channels S11/S12 and S21/S22 are used to be connected to the safety components at the site (For example the safety barriers) and if the area is evacuated then these channels will be activated.

Safety Barriers in Wiring Diagrams

As a result, the NO contacts of the Safety Relay (Output Contacts 13/14 and 23/24) become closed.

Therefore, our 13-14 NO contacts of the relays (KA1306 and KA1307) become closed.

How to Read Wiring Diagrams For Dummies

In this way, our 24-volt power will be transferred to page 12, column zero.

What is Wiring Diagram

Let’s pause this part here and we’ll continue the next part by reading and understanding the PLC, VFD, and their power and signal cabling section of this control panel wiring diagram.

You can read Part 2 of this article here.

Thanks for reading another article. Please spread the word by sharing this article:

Our YouTube Channel

Contact Us

Have a question or suggestion?

[email protected]

Youtube channel